Yazar "Inceoglu, Serkan" seçeneğine göre listele
Listeleniyor 1 - 4 / 4
Sayfa Başına Sonuç
Sıralama seçenekleri
Öğe Cortex of the pedicle of the vertebral arch. Part II: microstructure(Amer Assoc Neurological Surgeons, 2007) Inceoglu, Serkan; Kilincer, Cumhur; Tami, Andrea; Mclain, Robert F.Object. Although the gross anatomy of the pedicle in the human spine has been investigated in great detail, knowledge of the microanatomy of trabecular and cortical structures of the pedicle is limited. An understanding of the mechanical properties and structure of the pedicle bone is essential for improving the quality of pedicle screw placement. To enhance this understanding, the authors examined human cadaveric lumbar vertebrae. Methods. In this study, the authors obtained seven human cadaveric,lumbar vertebrae. The lateral and medial cortices of these pedicle specimens were sectioned and embedded in polymethylmethacrylate. Cross-sectional slices of cortex were obtained from each specimen and imaged with the aid of a high-resolution light microscope. Assessments of osteonal orientation, determinations of relative dimensions, and histomorphometric studies were performed. Results. The cortex of the pedicle in each human lumbar vertebra had an osteonal structure with haversian canals laid down mainly in the anteroposterior (longitudinal) direction. The organization of osteons across the transverse cross-section was not homogeneous. The layer of lamellar bone that typically envelops cortical bone structures (such as in long bones) was not observed, and the lateral cortex was significantly thinner than the medial cortex (p < 0.05). Conclusions. The cortical bone surrounding the pedicle differed from bone in other anatomical regions such as the anterior vertebral body and femur. The osteonal orientation and lack of a lamellar sheath may account for the unique deformation characteristics of the pedicle cortex seen during pedicle screw placement.Öğe Cortex of the pedicle of the vertebral arch.: Part 1(Amer Assoc Neurological Surgeons, 2007) Inceoglu, Serkan; Kilincer, Cumhur; Tami, Andrea; Mclain, Robert F.Object. Elastic deformation has been proposed as a mechanism by which vertebral pedicles can maintain pullout strength when conical screws are backed out from full insertion. The response to the insertion technique may influence both the extent of deformation and the risk of acute fracture during screw placement. The aim of this study was to determine the deformation characteristics of the lumbar pedicle cortex during screw placement. Methods. Lumbar pedicles with linear strain gauges attached at the lateral and medial cortices were instrumented using 7.5-mm pedicle screws with or without preconditioning by insertion and removal of 6.5-mm screws. The strains and elastic recoveries of the medial and lateral cortices were determined. Results. Mean medial wall strains tended to be lower than mean lateral wall strains when the 6.5-mm and 7.5-mm screw data were pooled (p = 0.07). After the screws had been removed, 71 to 79% of the deformation at the lateral cortex and 70 to 96% of the deformation at the medial cortex recovered. When inserted first, the 7.5-mm screw caused more plastic deformation at the cortex than it did when inserted after the 6.5-mm screw. Occasional idiosyncratic strain patterns were observed. No gross fracture was observed during screw placement. Conclusions. Screw insertion generated plastic deformation at the pedicle cortex even though the screw did not directly contact the cortex. The lateral and medial cortices responded differently to screw insertion. The technique of screw insertion affected the deformation behavior of the lumbar pedicles. With myriad options for screw selection and placement available, further study is needed before optimal placement parameters can be verified.Öğe Effects of angle and laminectomy on triangulated pedicle screws(Churchill Livingstone, 2007) Kilincer, Curnhur; Inceoglu, Serkan; Sohn, Moon Jun; Ferrara, Lisa A.; Benzel, Edward C.We aimed to demonstrate the effect of angle and laminectomy on paired pedicle screws to determine whether a 90 degrees screw angle is optimal as has been previously suggested. According to the angle between right and left screws, 28 calf vertebrae were divided into three groups and instrumented as follows: Group I: 60 degrees screw angle; Group II: 90 degrees angle; Group III: 60 degrees angle with laminectomy. The screws were connected using rods and cross-fixators and tested to peak pullout force. Triangulated pedicle screws provided 76.5% more pullout strength than single screws. Most of the specimens failed through loss of convergence angle (toggling of screws on the rods) and subsequent uni- or bilateral screw pullout. Mean +/- SD peak loads were: Group I: 2071 +/- 622 N; Group II: 1753 +/- 497 N; Group III: 2186 +/- 587 N. The differences were not significant (p > 0.05). 90 degrees triangulation was not associated with a superior pullout performance versus conventional 60 degrees triangulation, suggesting that achieving additional triangulation angle is not necessary to obtain increased pullout strength. Laminectomy did not alter the effect of triangulation on fixation strength. (c) 2006 Elsevier Ltd. All rights reserved.Öğe Screw design alters the effects of stress relaxation on pullout(Ios Press, 2008) Inceoglu, Serkan; Kilincer, Cumhur; McLain, Robert F.Stress relaxation during pullout of a pedicle screw decreases the peak load and stiffness of the bone-screw interface. However, it is unknown whether this can be generalized to all types of screw designs. This study aimed to show whether screw design altered the effects of stress relaxation on the mechanical performance of the pedicle screw during pullout. Twelve calf vertebrae were obtained: six vertebrae were instrumented with 7.5 x 40 mm conical pedicle screws and the other six with 5.0 x 40 mm cylindrical pedicle screws. The screws with two different designs were pulled out using either a standard pullout or a stress relaxation pullout protocol. Both bone-screw interfaces had lower stiffness in the stress relaxation pullout model than in the standard pullout model, but it was significant in only the cylindrical design group (P < 0.05). However, the stress relaxation and standard pullout models did not yield any difference in peak loads in either screw type. Although stress relaxation at the bone-screw interface can alter the mechanical performance of the screw, this may be eliminated by modifying the screw design. A better understanding of viscoelastic properties of the bone-screw interface may help improve implant design and thus, clinical outcomes.
